Thứ Năm, 21 tháng 1, 2016

BÀI 11 : ĐẾM TỪ 0 ĐẾN 9 SỬ DỤNG 2 NÚT NHẤN PIC16F887 XC8

- Đây là ảnh mô phỏng protues.
đếm từ 0 đến 9 sử dụng 2 nút nhấn pic16f887
- Đây là code chương trình.
#include <stdio.h>
#include <stdlib.h>
#define _XTAL_FREQ 8000000
#include <xc.h>
// CONFIG1
#pragma config FOSC = HS        // Oscillator Selection bits (HS oscillator: High-speed crystal/resonator on RA6/OSC2/CLKOUT and RA7/OSC1/CLKIN)
#pragma config WDTE = OFF       // Watchdog Timer Enable bit (WDT disabled and can be enabled by SWDTEN bit of the WDTCON register)
#pragma config PWRTE = OFF      // Power-up Timer Enable bit (PWRT disabled)
#pragma config MCLRE = OFF      // RE3/MCLR pin function select bit (RE3/MCLR pin function is digital input, MCLR internally tied to VDD)
#pragma config CP = OFF         // Code Protection bit (Program memory code protection is disabled)
#pragma config CPD = OFF        // Data Code Protection bit (Data memory code protection is disabled)
#pragma config BOREN = OFF      // Brown Out Reset Selection bits (BOR disabled)
#pragma config IESO = OFF       // Internal External Switchover bit (Internal/External Switchover mode is disabled)
#pragma config FCMEN = OFF      // Fail-Safe Clock Monitor Enabled bit (Fail-Safe Clock Monitor is disabled)
#pragma config LVP = OFF        // Low Voltage Programming Enable bit (RB3 pin has digital I/O, HV on MCLR must be used for programming)
// CONFIG2
#pragma config BOR4V = BOR40V   // Brown-out Reset Selection bit (Brown-out Reset set to 4.0V)
#pragma config WRT = OFF        // Flash Program Memory Self Write Enable bits (Write protection off)
unsigned char  const SEGMENT_MAP[10] = {0x3F,0x06,0x5B,0x4F,0x66,0x6D,0x7D,0x07,0x7F,0x6F};
void main(void) 
{
     ANSELbits.ANS0 = 0; // OFF ADC 
     ANSELbits.ANS1 = 0; // OFF ADC 
     TRISC = 0;           //Set PortB to all outputs
     PORTC = 0;
     TRISAbits.TRISA0 = 1;             //Set PortC.0 as input
     TRISAbits.TRISA1 = 1;
     char digit=0;
     while(1)
     {
     if (!RA0)        //Check if switch SW1 is closed
     {
     __delay_ms(100); //wait for 100ms
     if(!RA0)       //Check if switch SW1 is still closed
     {
     PORTC = (SEGMENT_MAP[digit]);
     __delay_ms(100); //Delay 1 second
     digit++;
     if (digit>9)
     digit=0;
     }
     }
     else
     {
     PORTC = (SEGMENT_MAP[digit]);         
     }
     if(!RA1)        //Check if switch SW1 is closed
     {
     __delay_ms(100); //wait for 100ms
     if(!RA1)       //Check if switch SW1 is still closed
     {
     PORTC = (SEGMENT_MAP[digit]);
     __delay_ms(100); //Delay 1 second
     digit--;
     if (digit==0)
     digit=9;
     }
     }
     else
     {
     PORTC = (SEGMENT_MAP[digit]);         
     }
    }
}
- Link download project Click here


EmoticonEmoticon